Р0340 0101 Неисправность в цепи датчика положения распределительного вала. OBD-II следует перевести прибор в режим “CLEARING CODES ” и. уменя SLIM и OVD загорелись машина заглохла что может.
What does that mean? The MAF (mass air flow) sensor measures the air entering the engine. The powertrain control module (PCM) uses that reading along with others to ensure proper fuel delivery at any given time. Basically this P0101 diagnostic trouble code (DTC) means that there is a problem with the Mass Air Flow (MAF) sensor or circuit. The PCM detects that the actual MAF sensor frequency signal is not within a predetermined range of the calculated MAF value for more than 4.0 seconds. Other MAF sensor circuit DTC trouble codes are P0100, P0102, P0103, and P0104 . This DTC is a generic OBD-II powertrain code. It is considered generic because it applies to all makes and models of vehicles (1996-newer), although specific repair steps may vary depending on the model. Symptoms The malfunction indicator lamp (MIL) will illuminate. You will likely not notice any serious drivability problems, although there may be symptoms such as rough running or stalling. Possible Solutions The simplest thing to do is to reset the code and see if it comes back. Then start with the cheapest, easiest repair procedures: Inspect for the following conditions: An incorrectly routed harness--Inspect the harness of the MAF sensor in order to verify that it is not routed too close to the following components: - The secondary ignition wires or coils - Any solenoids - Any relays - Any motors A low minimum air rate through the sensor bore may cause this DTC to set at idle or during deceleration. Inspect for any vacuum leaks downstream of the MAF sensor. A wide open throttle (WOT) acceleration from a stop should cause the MAF sensor g/s display on the scan tool to increase rapidly. This increase should be from 6-12 g/s at idle to 230 g/s or more at the time of the 1-2 shift. If the increase is not observed, inspect for a restriction in the induction system or the exhaust system. The barometric pressure (BARO) that is used in order to calculate the predicted MAF value is initially based on the MAP sensor at key ON. When the engine is running the MAP sensor value is continually updated near WOT. A skewed MAP sensor will cause the calculated MAF value to be inaccurate. The value shown for the MAP sensor display varies with the altitude. With the ignition ON and the engine OFF, 103 kPa is the approximate value near sea level. This value will decrease by approximately 3 kPa for every 305 meters (1,000 feet) of altitude. A high resistance on the ground circuit of the MAP sensor can cause this DTC to set. Any loss of vacuum to the MAP sensor can cause this DTC to set. If you suspect the condition may be related to aftermarket accessories, refer to Checking Aftermarket Accessories in Wiring Systems. Source: ChevyAvalancheFanClub P0101 MAF Sensor Repair Video This video is not produced by us, it is here as an aid in resolving your P0101 trouble code (DTC). NOTE: This information is presented for information purposes only. It is not intended as repair advice and we are not responsible for any actions you take on any vehicle. All information on this site is copyright protected. If you want to share this article or information with others, please link to this page, don't copy and paste it elsewhere.
The mass airflow sensor (MAF) measures the amount of air entering the engine. The OBD-II code P0101 is set when the signal from the mass air flow sensor is.
P0101 Trouble Code - Mass Air Flow (MAF) Circuit Range/Performance Problem
Using a U480 Code Reader on a 1999 BMW Z3 2.0 No faults, just trying I got DTC 2 Fault:01 Pend: 01 01 /02 P0430P What do all this mean?
Description of vehicle trouble code P0101 - Mass Air Flow (MAF) Circuit Range/ Performance Problem including diagnosis and repair tips.